Waekon 20560 Use and Care Manual Page 1

Browse online or download Use and Care Manual for Cable network testers Waekon 20560. Waekon 20560 Use and Care Manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Instructions
The ABS Sensor Pinpoint Tester and Flex Probe adapters quickly
and easily isolate the sensor from the vehicle harness and
control module. The tester checks both active and passive
sensors for proper voltage, frequency output and reluctor wheel
(tone ring) integrity. The tester will also check the passive sensor
for opens and shorts.
(2) Terminal Round
Extra Large Male
(2) Terminal Round
Medium Male
(2) Terminal Round
Small Male
(2) Terminal Spade
Small Male
Main control unit
(2) Terminal Spade
Small Female
(2) Terminal Alligator
(2) Terminal Round
Small Female
(2) Terminal Round
Medium Female
Interface Cable
19121-016
©2011 Hickok Inc. All rights reserved.
To Replace the Battery
The tester uses a standard 9 volt battery. If the battery is too low
to operate the tester the PWR LED will  ash and then the tester
will automatically turn o .
The battery can easily be accessed by removing the plug located
on the back of the tester.
Customer Care &Tech Support:
(800) 342-5080
Don’t forget to check out other testers, equipment and parts at
our websites. Access our Quick-n-E-Z Parts and Service from any
of these sites 24/7 for ordering parts or service.
www.hickok-inc.com
www.waekon.com
www.quick-n-ezparts.com
10514 Dupont Ave.
Cleveland, OH 44108
Warranty
Subject to the conditions that follow and are noted below, this
product is warranted to be free from defects in material and
workmanship, under proper use and in accordance with the
manufacturers written recommendation and speci cations, for
a period designated below on all products:
This product carries a one year limited warranty.
The manufacturer’s obligation under this warranty is limited
to unaltered products returned to the manufacturer by the
initial end user of the new products. Therefore, this warranty
does not cover any products resold by the end user to third
parties, nor any reconditioned products sold as such, by the
manufacturer. The sole remedy for any such defect shall be the
repair, or replacement, of the product at the sole discretion of
the manufacturer. This warranty does not cover expendable
parts, such as batteries, nor does it cover shipping or handling.
In addition, manufacturer is not liable for any loss or damage to
product during shipping.
In the event it is determined that the product has been
tampered with, or altered in any way, this warranty is void and
all claims against the product will not be honored. All warranty
claims must be submitted as outlined by the manufacturer
and shall be processed in accordance with the manufacturers
established warranty claim procedures. These procedures
include provisions that proof of purchase must be established
(by either warranty card from the seller or by point of purchase
receipt) and that the manufacturer will make every attempt to
return ship the product within one business day from receipt of
the returned product, freight prepaid.
In addition, all maintenance procedures, as outlined by the
product manuals, should be followed for the warranty to be
kept in force. Should the product not be used in accordance
with procedures as speci ed, or if the product otherwise fails
outside of the warranty, the manufacturer reserves the right
to make such judgment and the party returning the product
will be noti ed that written noti cation will be necessary to
repair the product at a cost which the manufacturer deems
as reasonable. The product will then be shipped back to the
customer, COD; or as the manufacturer deems appropriate.
This is the only authorized manufacturer’s warranty and is in lieu
of all other expressed, or implied, warranties or representations,
including but not limited to any implied warranties of
merchantability or  tness or any other obligations on the part
of the manufacturer. In no event will the manufacturer be liable
for business interruptions, loss of pro t, personal injury, costs
of delays, or any special, indirect, incidental or consequential
damages, costs or losses.
©2011 Hickok Inc.
All rights reserved
Page view 0
1 2

Summary of Contents

Page 1 - All rights reserved

InstructionsThe ABS Sensor Pinpoint Tester and Flex Probe adapters quickly and easily isolate the sensor from the vehicle harness and control module.

Page 2

CONTOLUNITABCGREENGREENFLEX PROBESVEHICLEHARNESS12 V(active sensor only)CONTOLUNITABCGREENGREENFLEX PROBESVEHICLEHARNESSCAR CHASSISBLACK12 V(active se

Comments to this Manuals

No comments